UPDATE production, logistics and delivery time for SATA HAT products

By Celina Xu 43 comments

Overall Situation and Status

It has been some time since we updated you, we are sorry about that but things have been keeping us quite busy over here.

We so much share the common frustration about delays and especially the fact that we have limited influence over it. The outbreak of the corona virus has become a huge challenge to the complete supply chain on one hand and of course and most importantly the daily lives of us all.

To be able to cope with the outbreak, strict measures had to be taken which will have an impact long after this outbreak is contained and managed.

Overall improvements have been seen in the last few days. That is very good! The measures of course stay in place which is understandable since the changes have to be proven sustainable.

This week many factories resumed work, which is also very good. The overall problem though is the lack of labor to get the performance back to where it was before the outbreak. The limitations on travelling, especially from heavily hit regions, still keep much of the labor away from Shenzhen.

The measures also affect logistics which means raw material will arrive late.

Factories have to outsource services (e.g. surface treatment for our cases, or extrusion for some parts) which adds uncertainty to delivery times. Most of the surface treatment plants e.g. did not even resume work yet.

The results are overall increased (or not confirmed) delivery times.
After checking all available options (e.g. even changing suppliers) we decided to stick with the existing channel because it is in the best interest of all.

In short it means that we can still not give you detailed shipment information at the moment, because one or more of the above mentioned problems exist. We did split the batch though, to at least be able to release goods step by step.

We still try to manage the shipments until the end of March, but many unanswered questions in our supply chain remain.

From now on we will release an update every week.

Extended Promotion time

Because of the situation explained we will extend the promotion until further notice.
 

Logistics / Shipment

International shipments from our warehouse have also been affected. With many international flights to China cancelled until April and beyond the available air cargo space has substantial shortage. It also affects our ability to deliver economy express to some destinations.

This service delivers the cargo to the destination country and then hands it over to the local post for delivery. The only fallback solution we now have is to ship with China Post.
We expect some of the shipment options to resume this week, overall the situation is difficult. DHL, UPS are affected, but do process as usual.

ROCK PI SATA HAT TOP BOARD Product details:

This time we would like to share some details about the sata hat top board. SATA HAT TOP BOARDWe did get some questions out of the community and we like to share the answers.
The Sata Top Board is both a tool to manage the temperature inside the case and a status information panel at the same time. The added software managed switch can be used to take action and/or scroll data on the screen.
 
Once you mounted all parts please install the provided software running the following script curl -sL https://rock.sh/get-rockpi-sata | sudo -E bash - 

The following features will be activated:

    • The big mounted PWM controlled fan makes sure the air flow is stable and disks and of course HAT and Raspberry Pi 4 are kept on acceptable temperature levels. PWM means - the fan´s rotating speed and noise are related to the temperature inside of the case. This is done with a temperature sensor and software which manages the RPM of the fan. This feature provides good noise management because the fan is not permanently spinning with full speed.

    • The second monitoring device is the OLED display. It provides frequent update on the status of the NAS. Standard information provided is e.g. CPU load, RAM usage of RASPI4, Temperature, IP address and disk information. The displayed content can be managed with adjusting the related config file under /dev/rockpi-sata.conf

    • The third feature is the small switch which can be assigned to different functions  via the same config file we mentioned above. Once you finished the modification of the configuration file you can reboot the NAS or restart the service with this command: sudo systemctl restart rockpi-sata.service

    You can find the complete product specs and installation details here: 

    If you need some more details don't hesitate to contact us on sales_cn@allnet.de

    Thank you for your ongoing patience and trust!
     

    43 comments

    • Colin

      Can’t help with the US thing, but my UK order has just arrived.
      They sent me an email saying they were dispatching it. A couple of days later the tracking number actually showed up on the tracking system, but no details – just “In Transit”. A few more days and it has arrived (I did try to track it yesterday)!
      27/05/2020 to today (03/06/2020) – I make that a week.

    • Joel

      Just out of curiosity for those that have recieved their kit in the US, from the time you got the notice that the item had shipped to when it started showing up with tracking updates on USPS, about how long was that?

    • Manny

      Ordered on February 23, 2020 and received on May 28, 2020. As KD stated the power supply is “massive.” I too have not completely assembled my kit, as I am awaiting for my drives from Amazon. Amazon currently do not have the drives (2.5 5400 RPM) in stock and estimated ship date will be June 13th. I will share a link once my device is fully assembled and operational. Build quality is above par! OUTSTANDING ALLNET! Thank you!!!

    • Frank Imeson

      Any chance we will see a 2 bay 3.5" NAS kit that uses a hat in the future? 3.5" drives are more practical and building one with cables is bulky and messy.

    • KD

      FWIW, I received my quad SATA kit today. I placed an order Feb 15. I haven’t assembled it yet, but just wanted to let others know that it might take long, but it should arrive.

      That being said, I am slightly disappointed that the power supply is a regular DC supply and not USB-C as in the original design. They did include a DC power supply, but its massive compared to the 45W USB-C supplies that I have.

    Leave a comment

    Login