Storage
QUAD SATA HAT KIT for your Raspberry Pi 4
Easily build your own NAS / Media-server based on Raspberry Pi 4
TOP Raspberry Pi Project 2020! @Novaspirit Tech https://youtu.be/BXidc8zdNis
QUAD SATA HAT KIT for your Raspberry Pi 4
Easily build your own NAS / Media-server based on Raspberry Pi 4
TOP Raspberry Pi Project 2020! @Novaspirit Tech https://youtu.be/BXidc8zdNis
Description
- mount up to 4x 2.5" HDD or SSD (max height 9.5mm)
- Software RAID 0/1/5
- HDD/SSD status LED online/activity/fault
- Utilizes two independent USB3 buses on Raspberry Pi 4
- DC Type (5.5/2.5) power input with support for 2.5inch drives and Raspberry Pi 4
- HDD suspend mode supported
- UASP support
- Capacity up to 16TB (e.g. 4x 4TB SSD)
- PWM controlled fan for HDD heat dispatching
- OLED display for IP Address/Storage info
- does only work with Raspberry Pi 4
- easy to set up and run
- Size (L/W/H) 94 x 70 x 173 mm
Product Content
- Quad SATA HAT board
- SATA HAT Top board, management board including OLED status display and active cooling
- HAT connector cable
- ecoPI Quad Sata case (aluminum)
- USB3.0 dual bus connector
- heat sink kit with PWM fan for Raspberry Pi 4
What is so special?
- smaller than a bottle of Coke
- fits into the smallest book shelf
- low noise PWM fans
- high capacity up to 16TB
- economic as surveillance system
- fast as media server
- backup server for your home
- OLED display for basic status information
- nice lean design
IMPORTANT:
You need to use a >=40W 12V DC Power supply to run this NAS!
Raspberry Pi 4 2/4GB is recommended
->>Rock Pi 4 Model C+ can be used as replacement<<-
BUT PLEASE NOTE:
The M.2 (M) 2230 up to 2T M.2 NVME SSD via PCIe 2.0 x4 interface must not be populated in this setup!
Just add your Raspberry Pi 4 (Rock Pi 4C+) to this Kit and your NAS is complete and it really looks great!
PENTA SATA KIT for Rock Pi 4 A/B
Easily build your own PCIe based NAS / Media-server with a Rock Pi 4
See how to assemble the Kit here: https://youtu.be/cwWkUQFGdm8
* order award (free 60W DC power supply) - limited stock available!
PENTA SATA KIT for Rock Pi 4 A/B
Easily build your own PCIe based NAS / Media-server with a Rock Pi 4
See how to assemble the Kit here: https://youtu.be/cwWkUQFGdm8
* order award (free 60W DC power supply) - limited stock available!
Description
- mount up to 4x 2.5" HDD or SSD (max height 9.5mm) + 1x ext HDD or SSD
- esatap connector for external SSD/HDD
- Software RAID 0/1/5
- HDD/SSD status LED online/activity/fault
- Utilizes PCIe gen2 4 lanes interface on Rock Pi 4
- DC power input for Rock Pi 4, 4x 2.5inch sata drives and 1x esatap 2.5 or 3.5" HDD/SSD
- HDD suspend mode supported
- UASP support
- Internal capacity up to 32TB (e.g. 4x 8TB SSD)
- PWM controlled fan for HDD heat dispatching
- OLED display for IP Address/Storage info
- does only work with Rock Pi 4
- huge heat-sink for Rock Pi 4 included (30% bigger)
- easy to set up and run
- Size (L/W/H) 94 x 70 x 175 mm
Product Content
- PENTA SATA HAT board
- SATA HAT Top board, management board including OLED status display and active cooling
- HAT connector cable
- ecoPI Penta Sata case (aluminum)
- High performance ribbon data cable and connector
- heat sink for Rock Pi 4
What is so special?
- smaller than a bottle of Coke
- fits into the smallest book shelf
- PCIe gen2 based SATA interface
- PWM controlled fan
- high internal capacity up to 16TB (e.g. 4x 4TB SSD)
- economically as a surveillance system
- fast as media server / cloud server
- backup server for your home
- OLED display for status information
- Backup your NAS with e.g. an external 3.5" esatap powered drive of your choice!
- nice lean design
IMPORTANT:
You need to use a 12V (>=5A) >=60W DC Power supply to run this NAS!
Rock Pi 4 A/B 4GB is recommended (Rock Pi 4 Model C is not supported)
eMMC is needed to boot the device
Just add your Rock Pi 4 and eMMC to this kit and your blasting NAS is complete!
PENTA SATA KIT for Rock Pi 4 Model A/B, A/B+ and Rock3A
Easily build your own PCIe based NAS / Media-server with a Rock Pi 4
PENTA SATA KIT for Rock Pi 4 Model A/B, A/B+ and Rock3A
Easily build your own PCIe based NAS / Media-server with a Rock Pi 4
See how to assemble the Kit here: https://youtu.be/cwWkUQFGdm8
*order bonus (free 60W DC power supply)!
Description
- mount up to 4x 2.5" HDD or SSD (max height 9.5mm) + 1x ext HDD or SSD
- esatap connector for external SSD/HDD
- Software RAID 0/1/5
- HDD/SSD status LED online/activity/fault
- Utilizes PCIe gen2 4 lanes interface on Rock Pi 4
- DC power input for Rock Pi 4, 4x 2.5inch sata drives and 1x esatap 2.5 or 3.5" HDD/SSD
- HDD suspend mode supported
- UASP support
- Internal capacity up to 32TB (e.g. 4x 8TB SSD)
- PWM controlled fan for HDD heat dispatching
- OLED display for IP Address/Storage info (customizable)
- does only work with Rock Pi 4 Model A/B, A/B+ and Rock 3A
- huge heat-sink for Rock Pi 4 included (30% bigger)
- easy to set up and run
- Size (L/W/H) 94 x 70 x 175 mm
Product Content
- PENTA SATA HAT board
- SATA HAT Top board, management board including OLED status display and active cooling
- HAT connector cable
- ecoPI Penta Sata case (aluminum)
- High performance ribbon data cable and connector
- heat sink for Rock Pi 4
What is so special?
- smaller than a bottle of Coke
- fits into the smallest book shelf
- PCIe gen2 based SATA interface
- PWM controlled fan
- high internal capacity up to 32TB (e.g. 4x 8TB SSD)
- economically as a surveillance system
- fast as media server / cloud server
- backup server for your home
- OLED display for status information
- Backup your NAS with e.g. an external 3.5" esatap powered drive of your choice!
- nice lean design
IMPORTANT:
You need to use a 12V (>=5A) >=60W DC Power supply to run this NAS!
Does not work with Rock Pi 4 Model C!
eMMC is needed to boot the device (because of stability and limited space)
Just add your Rock Pi 4 and eMMC to this kit and your blasting NAS is complete!
Build your NAS based on Raspberry Pi 3/4 or Rock Pi 4 with up to 4 HDD/SSD and up to a capacity of 20TB. (depending on your setup)
Dual/Quad SATA HAT utilizes the dual USB3 bus on the Raspberry Pi 4
Build your NAS based on Raspberry Pi 3/4 or Rock Pi 4 with up to 4 HDD/SSD and up to a capacity of 20TB. (depending on your setup)
Dual/Quad SATA HAT utilizes the dual USB3 bus on the Raspberry Pi 4
Features
- up to 4x HDD/SSD´s - 2.5 or 3.5inch storage is supported
- utilizes two independent USB3 buses on Raspberry Pi 4
- 12V DC Type power input for powering 2.5inch drives and Raspberry Pi 4
- External standard ATX power supply support for 3.5inch HDD´s
- PWM Fan and heatsink for Raspberry Pi 4 CPU cooling
- HDD suspend mode supported
- UASP support
- Software RAID 0/1/5 support
- Optional Top board with PWM controlled fan for HDD heat dispatch, OLED display for IP address, storage and status information and function assignable switch
For 3.5inch HDD setups, a 12V 5A DC PS or standard ATX PSU is recommended to power the HDD´s and the Raspberry Pi. With 4x 3.5inch HDD´s the PSU should provide at least 60W or more.
PLEASE NOTE: ! DOES NOT FIT THE PREVIOUS CASE KIT !

For 2.5inch HDD setups the 12V DC 4A power adapter ( >=30W power adapter ) is sufficient to power the disk drives and the Raspberry Pi 4 together.
It is important to mention that the power connector on the SATA HAT must be used to power up the NAS with Raspberry Pi 4.

Performance
The Quad SATA HAT utilizes two high performance JMS561 (one JMS561 for the Dual SATA HAT) and provides up to 400MB/s read/write performance with four disks in RAID0 mode.
Product Content
What you need to run this NAS?
For 2.5inch HDD operation
12V DC 4A/5A Power adapter
2.5inch HDD/SSD
Raspberry Pi 4 with OS running
For 3.5inch HDD operation
12V DC 5A or ATX PSU > 60W
3.5inch HDDs
SATA cables
Raspberry Pi 4 with OS running
PLEASE NOTE: ! DOES NOT FIT THE PREVIOUS CASE KIT !
Build your NAS based on Radxa´s Rock Boards with up to 5 HDD/SSD and up to 100TB capacity
Build your NAS based on Radxa´s Rock Boards with up to 5 HDD/SSD and up to 100TB capacity
The Penta SATA HAT utilizes the M.2/PCIe interface on RADXA´s ROCK Boards* to provide up to 5 SATA ports. This HAT works only with Rock Pi 4 mounted on the heat sink.
The concept of 4 internal SATA and one eSATAp design was chosen because it makes the setup more flexible for the use of external disks.
Features
- Up to 5x HDD/SSD, 2.5inch and 3.5inch storage is supported, max storage 100TB
- 4x SATA
- 1x eSATA with power
- utilizes two lanes of the PCIe 2.1 bus on Rock Pi 4
- DC power input with support for both 2.5inch drives and ROCK Pi 4
- External standard ATX power supply support for 3.5inch HDD
- HDD suspend mode support
- Software RAID 0/1/5 support
- Optional PWM control fan for HDD heat management
- Optional OLED display for IP / Store information
- PLEASE NOTE: You need to order the heat-sink with Rock 4, otherwise the Penta HAT can not be mounted on top. For use with Rock 3A please purchase the base plate for proper installation.
eSATAp
To fully take advantage of the 5th SATA port, an eSATA connector was implemented which can be exported e.g. out of the case. The eSATA connector provides both data and power. It can directly drive a 3.5inch HDD via a single cable.

Performance
The Penta SATA HAT is powered by the JMB585 with 2 lanes 5Gbs PCIe buses with up to 10Gbps bandwidth. With 5 SSD's configured in Raid0 mode, speed of up to 803MB/s can be achieved.

Product Content
Penta SATA HAT board
M.2 interface board with high speed Ribbon connector cable
Penta SATA HAT works with the following boards:
Rock 4 Model A/A+, B/B+
Rock 3 Model A
Rock5 Model A - please choose the right option
optional: SATA HAT Top Board
For Dual/Quad and Penta SATA HAT
To monitor the SSD/HDD´s and display some basic information of the NAS, the TOP Board was designed.
For Dual/Quad and Penta SATA HAT
To monitor the SSD/HDD´s and display some basic information of the NAS, the TOP Board was designed.
It provides PWM FAN control, IP address info and other details via the implemented OLED display.
The select button can change the display content and as well power the device off. This button can also be assigned to custom functions on request via software settings.
A ribbon cable connects the SATA HAT with the Top board.
Product Content
SATA HAT Top board
Ribbon connector cable
You bought your QUAD SATA HAT for Raspberry Pi 4 and want to get the case for it?
Buy me! :-)
You bought your QUAD SATA HAT for Raspberry Pi 4 and want to get the case for it?
Buy me! :-)
- Aluminum case for QUAD SATA HAT for Raspberry Pi 4
- Base Plate
- Acrylic cover with vent openings
- Screws, bolts and silicon feet for vibration free operation included
Note:
Please make sure you also bought the "SATA HAT top board incl. OLED and PWM fan". It will work without this board but the heat management might not be really sufficient and you miss out the switch and of course status display on top.
Universal and flexible 12V 5A DC power supply with exchangeable power plug
Stable and sufficient power for your Sata HAT and SATA KIT setup!
Universal and flexible 12V 5A DC power supply with exchangeable power plug
Stable and sufficient power for your Sata HAT and SATA KIT setup!
INPUT
- 100-240V
- ~ 50/60Hz 1.5A
OUTPUT
- Regulated +12VD
- Current 5A
CERTIFICATES
- CE, GS, CB, UL/CUL, FCC, PSE, CCC, RoHS, Reach
SPECIAL
- exchangeable power plug for US, EU, UK, AU
- (other country plugs on request)
DIMENSION
- 100x50x40mm
- wire length 1m
- DC Barrel (5.5x2.5) 90°
PRODUCT CONTENT
- power supply
- country plug
- additional country plugs (optional)
Plug on eMMC 5.1 storage media for Rock 3A /Rock 4 /Rock5A B /VisionFive2
Available as 16GB/ 32GB/ 64GB or 128GB version.
Plug on eMMC 5.1 storage media for Rock 3A /Rock 4 /Rock5A B /VisionFive2
Available as 16GB/ 32GB/ 64GB or 128GB version.
As well compatible to ODroid and Pine
PLEASE NOTE: For your convenience please order as well the eMMC to uSD adapter board or the eMMC USB3.1 Reader. It makes it easy to flash software images on to the eMMC module.
Supported boards:
ROCK PI E, ROCK 3C, 4C+, SE
eMMC to uSD (micro SD) adapter board for effortless flashing SW images on to eMMC modules.
Steps:
- Click the eMMC module on to the adapter board.
- Use a micro sd card reader and insert the adapter board with the mounted eMMC module.
- Plug the micro sd card reader into your computer. (the eMMC module will appear as device in your storage manager)
- Now flash the software image on to the eMMC module.
Balena Etcher is a very convenient tool for flashing the image on to the eMMC.
eMMC to uSD (micro SD) adapter board for effortless flashing SW images on to eMMC modules.
Steps:
- Click the eMMC module on to the adapter board.
- Use a micro sd card reader and insert the adapter board with the mounted eMMC module.
- Plug the micro sd card reader into your computer. (the eMMC module will appear as device in your storage manager)
- Now flash the software image on to the eMMC module.
Balena Etcher is a very convenient tool for flashing the image on to the eMMC.
True blasting USB3.1 performance!!
Flash your SW image on to eMMC with true USB3.1 speed!
True blasting USB3.1 performance!!
Flash your SW image on to eMMC with true USB3.1 speed!
- High speed USB3.1 Gen2 GL3227E controller
- Write speed up to 150MB/s
- Dual mount for eMMC module
- Support eMMC HS400 mode
- Support ROCK PI eMMC modules up to 128GB
- Compatible to ODROID / Pine64 eMMC modules
- Support GPT partition table and firmware
Use your old eMMC module as USB drive..
Supported under Linux, Windows, MacOS
To make the connection of external HDD/SSD to e.g. our Penta SATA HAT as convenient as possible we added this cable to our store.
To make the connection of external HDD/SSD to e.g. our Penta SATA HAT as convenient as possible we added this cable to our store.
Dual power (5V, 12V)
Length 0.5m
Just plug in your disk - it will be up and running in no time!